Precision, Performance, Confidence. ™

LogWare III Version 3.1 Installation

 

This installation consists of two sections: The first one is about the database installation which must be done first, and the second one is about the LogWare III installation.

 

Section 1:

Installation of Database “PostgreSQL” latest version. 

Click on the link below to find and download the LATEST VERSION of PostgreSQL:

https://www.enterprisedb.com/downloads/postgres-postgresql-downloads

Steps 1 through 8 show an example in how to download database version 13.2, and you need to follow the same process to install the LATEST VERSION of PostgreSQL.

 

1- After you identify the LATEST VERSION click on download.

Version:                 PostgreSQL 13.2

Operating System:  Windows x86-64

mceclip1.png

2- Click “Yes” in the below screen:

mceclip2.png

3- Click Next in the following screens:

mceclip3.png

mceclip4.png

4- Make sure that all boxes have check marks, and then click next in the following screens.

mceclip5.png

mceclip6.png

5- Use the password: FlukePGSQLDatabase9! and then click Next

mceclip7.png

6- By default, the port number is usually 5432, but if for any reason another port number is showing in the below screen please keep the new one.

mceclip8.png

7- Select Next in the following screens:

a)

mceclip9.png

b)

mceclip10.png

c)

mceclip11.png

8- After “Completing the PostgreSQL Setup Wizard” uncheck the stack builder option and click “Finish”.

mceclip12.png

 

Section 2

II-LogWare III Version 3.1 Installation

9- Insert the CD that contains the software in your computer and select 9936A. Proceed to install the “LogWare III software” by clicking on “Setup.exe”. Or you can download the latest version by clicking on the link below “LogWare III v3.1 Working Demo” then run the “Setup.exe”.

https://us.flukecal.com/literature/software-downloads/software/logware-iii-v21-working-demo

mceclip13.png

 10- Select Next in the following screens:

mceclip14.png

mceclip15.png

11- Select “Stand-Alone” for a single user configuration. Or select “Client/Server” for a multiuser configuration where one computer is required to act as the Server, and one or more computers are required to act as the clients.

Select Stand-Alone in the below screen, OR you can select Client/Server then go to step#18

Section 2.1

Stand-Alone Installation:

mceclip16.png

 12- Select Expert installation then click on NEXT.

mceclip17.png

13- Enter the Serial Number that is located on the CD’s envelop or leave it blank if you are installing the Demo Version. The serial number is a combination of 18 letters and numbers.

mceclip18.png 

14- By default, the port on the screen below should be 5432, and it should match the one from step# 6. If they don’t match, type the same port number from step# 6 on the screen below. The password for the database is: FlukePGSQLDatabase9!

mceclip19.png

15- Click OK.

mceclip20.png

 16- Click on “Install”

mceclip21.png

17- Click “Finish”

mceclip22.png

After finishing the Stand-Alone installation please go to Step# 31.

Section 2.2

Client-Server Installation

18- Select Expert Installation, then click on NEXT.

mceclip23.png

19- Enter the serial number, then click NEXT.

mceclip24.png

20- If you don’t have a dedicated server in your Network, and a regular computer is acting as the server you are limited to 10 client computers. Click YES.

mceclip25.png

21- Click NEXT in the following screen.

mceclip26.png

22- The folder “LW3Shared” must be shared with the other Fluke LogWare III client computers. It is recommended to keep the default name shown below. Click NEXT.

mceclip27.png

23- By default, the port number on the screen below should be 5432, and it should match the one from step# 6. If they don’t match, type the same port number from step# 6 on the screen below. The password for the database is: FlukePGSQLDatabase9! Then click NEXT.

 

mceclip28.png

24- Click OK

mceclip29.png 

25- Click Install.

mceclip30.png

26- Click NEXT.

mceclip31.png

27- Click YES to print the To Do list.

mceclip32.png

 28- Click “Finish” and the computer will restart.

mceclip33.png

 29- Go to each of the client computers, and in the search bar type “Run” and then select the R App. In the open field of the Run App enter:

mceclip34.png 

SERVER NAME: Go to the server computer and identify the server’s name

Share Name: Is the name of the file from step# 22. Default share name is: LW3Shared

Finally click OK to install the client.

30- Now go to the following folder in the Server Computer:

C:\Program Files\PostgreSQL\Database version being used\data\pg_hba.conf (right click and edit with notepad)

Go to the bottom of this file and add the following lines for each client computer. For the example below we are using 2 client computers.

host logware3 postgres (IP address client computer1)/16 md5 

host logware3 postgres (IP address client computer2)/16 md5 

After this is done save the file, and the bottom section of the file should look like the screenshot below, and highlighted with yellow are the lines we added for each client computer:

mceclip35.png

31- Your desktop should have now an icon that says “LogWare III Client”. Please double click on it to launch LogWare III.

mceclip36.png

a) The following message will show.

mceclip37.png

 

b) Insert the CD that contains the license and then apply it.

mceclip38.png

c) Click OK.

mceclip39.png

d) The default password is LogWare.

mceclip40.png

 

 

 

Have more questions? Submit a request

Comments

Please sign in to leave a comment.